Claim explorer / evidence thread
Claim 73840
MYRV 12024 • Stephanie • Paid • open-range
risk 0.00
deadline Overdue / escalation ready
images 0
matched 3
Warranty deadline timeline
Track where the claim sits in the recovery workflow, how many days have elapsed, and whether the auto-approval window or payment deadline is already in play.
Uploaded
Completed stage
20d elapsed • 0d remaining
Analyzed
Completed stage
20d elapsed • 0d remaining
Awaiting OEM
Completed stage
20d elapsed • 0d remaining
Auto-Approved
Completed stage
20d elapsed • 0d remaining
Payment Due
Completed stage
20d elapsed • 0d remaining
Escalation Eligible
Completed stage
20d elapsed • 0d remaining
Resolved
Overdue / escalation ready
20d elapsed • 0d remaining • Overdue
AI Claim Analysis
Estimated Recovery Amount
$375.00
What this claim may still be worth based on current evidence.
Compliance Score
100/100
Higher is cleaner. Lower means more missing support, more friction, or more OEM pushback.
Violations Detected
1
No flagged violation label yet — keep reviewing payment and document evidence
Missing Items
0
No active evidence gaps are listed.
Deadline Status
Overdue / escalation ready
20 days open in the visible workflow.
Recommended Action
Escalate to State
This is the fastest next move from the current workflow stage.
US dispute readiness
Evidence packet check
Operational preflight for US warranty escalation: packet size, chronology, cross-references, witness checks, source grounding, and backup evidence.
Estimated pack size
5
Proxy count from docs, images, comments, and claim lines. Actual PDF pages still need final preflight.
Evidence packet lane
Compact packet candidate
Small enough for a compact escalation packet, assuming final PDFs stay clean.
Chronology
Ready to order
Visible span: Aug 12, 2026, 4:36 PM to Aug 26, 2026, 3:08 AM.
Indexed evidence
2 docs / 0 images
Use only the strongest evidence in the escalation packet; keep the rest as support material.
Cross-reference base
Available
Line items, comments, or gap flags can be tied back to supporting material.
Witness verification
Human verification required
Any statement or affidavit output must be checked by the witness before use.
AI / citation gate
Manual check required
Escalation material must keep facts, inferences, citations, and source documents separated.
Expert evidence pressure
Not signalled
No expert-evidence trigger is visible from the current image rollup.
Escalation posture
Monitor
20 days open in the visible workflow; risk score 0.00.
Claim Summary
Evidence summary
No evidence summary yet.
Path
/home/openclaw/nas/Dropbox/MYRV 12024/8- Claims Paid/August 2026/Open Range/73840/Paid claim.pdf
Timeline
First seen Aug 12, 2026, 4:36 PM • last seen Aug 26, 2026, 3:08 AM
Evidence flags
No active evidence gap flags
Comment Intelligence
Thread depth
6 indexed side comments on this claim.
Latest visible thread signal
Aug 25, 2026, 9:34 AM • processor • Claim J01606793 paid $678.36 check 486066 8/24/2026
Role mix
Dealer 0 • OEM 0 • Processor 6
Decision cues
Denial signals 0 • info / missing-doc asks 0 • approval signals 3
Best move
Thread shows approval language — verify payment / closeout.
Quick Actions
Back to search results
Run the same search again.
Open focused evidence thread
Jump straight into Dropbox side comments, notes, and support documents.
Open claim explorer
Return to the main recovery queue view.
Open evidence room
See the quick-rule cards first, then open the legal basis only if needed.
Images
No browser-previewable images were available for this claim yet.
Claim Lines
complaint
CUSTOMER STATES STOVE DOES NOT STAY LIT OR LIGHT ON ITS OWN
partial-match • confidence 0.38
cause
The thermal couple on both burners is right up against the burner and will not allow the flame to be seen when there is a pot or a pan on the burner.
matched • confidence 0.67
correction
I removed the two burners, the two knobs and the stove, top cover, repositioned the thermocouples to allow flame to be seen while theres a pan on the burner. This stove does not have igniters, so it will not ignite on its own by design. I had to remove the entire stove assembly in order to get the model serial number that is on the bottom of the stove pan. I reinstalled the stove reinstalled the top reinstalled the burners and the knobs. Filled a pan with water. And set on both burners one at a time to test *60942* function. Stove top now works as designed. Job completed. .50HRS
matched • confidence 0.87
complaint
CUSTOMER STATES SHOWER LEAKING ON FLOOR / DRAINING TOWARDS KITCHEN AND ON GROUND BELOW SHOWER
partial-match • confidence 0.41
cause
The fittings on the P-trap came unglued
partial-match • confidence 0.46
correction
I removed the access panel at the bottom of the shower and noticed the P-trap was in two pieces. I dont have access to the backside of the P-trap to remove from the shower drain. I removed all the screws out of the two end pieces, two corner pieces, and the three pieces of trim that cover the top lip of the shower surround. I pulled the shower surround up and removed the P-trap and noticed that the glue joint was barely glued together to begin with. I cleaned off all the excess glue reassembled it glued in place with ABS glue. Put the P-trap back on the bottom of the shower pan and tried to reinstall it, and thats when I see the reason why it was barely glued is because its 3/4 of an inch too tall now. I had to cut the glued pieces back apart and using my PVC drill drill out the pieces of glued in pipe from the fittings get another piece of ABS and cut the length. I dry fit everything together make sure everything would fit. When Page 1 of 2 © 2026 Integrated Dealer Systems *73840* everything fit properly, the angle of the drain that goes through the floor wasnt gonna fit. I had to cut that Promised Date: 11 AUG 26 W/O: 73840 pipe, fit everything together and using a rubber coupler repair the pipe that goes down through the floor. I had to scrape all the silicone off of the trim that covers the shower pan, reinstall all of those along with the corner trims and end pieces. I ran the water for five minutes down the P-trap. No leaks were noticed. Resealed the shower pan, and reinstall the access plate. 3.00HRS
matched • confidence 0.98
Evidence Thread
Ashlee Olsen
processor • Aug 12, 2026, 4:36 PM
submitted PA#J01606793-001-002
Stephanie Kendziorski
processor • Aug 19, 2026, 10:46 AM
@Brian P Job 1 approved .5 hours
Job 2 approved 3.0 hours
Stephanie Kendziorski
processor • Aug 19, 2026, 11:40 AM
@Brian P Hey! I submitted line 1 for payment, but I have to wait on line 2. This is the one I emailed on earlier, they have your approved labor at $3.00 because they accidentally posted your rate at $1/hour. Once I get an email back that it has been corrected, I will submit.
Stephanie Kendziorski
processor • Aug 19, 2026, 11:41 AM
Submitted line 1 for payment, see note to Brian for issue with line 2.
Stephanie Kendziorski
processor • Aug 20, 2026, 1:59 PM
Submitted line 2 for payment
Stephanie Kendziorski
processor • Aug 25, 2026, 9:34 AM
Claim J01606793 paid $678.36 check 486066 8/24/2026
Claim Files
73840F.pdf
main-pdf • Aug 19, 2026, 11:30 AM • 311,542 bytes
/home/openclaw/nas/Dropbox/MYRV 12024/8- Claims Paid/August 2026/Open Range/73840/73840F.pdf
73840.pdf
main-pdf • Aug 12, 2026, 10:18 AM • 312,367 bytes
/home/openclaw/nas/Dropbox/MYRV 12024/8- Claims Paid/August 2026/Open Range/73840/73840/73840.pdf