Claim explorer / evidence thread
Claim 74156
MYRV 12024 • Stephanie • Paid • rpod
risk 0.00
deadline Overdue / escalation ready
images 0
matched 1
review 3
Warranty deadline timeline
Track where the claim sits in the recovery workflow, how many days have elapsed, and whether the auto-approval window or payment deadline is already in play.
Uploaded
Completed stage
27d elapsed • 0d remaining
Analyzed
Completed stage
27d elapsed • 0d remaining
Awaiting OEM
Completed stage
27d elapsed • 0d remaining
Auto-Approved
Completed stage
27d elapsed • 0d remaining
Payment Due
Completed stage
27d elapsed • 0d remaining
Escalation Eligible
Completed stage
27d elapsed • 0d remaining
Resolved
Overdue / escalation ready
27d elapsed • 0d remaining • Overdue
AI Claim Analysis
Estimated Recovery Amount
$250.00
What this claim may still be worth based on current evidence.
Compliance Score
100/100
Higher is cleaner. Lower means more missing support, more friction, or more OEM pushback.
Violations Detected
1
OEM Response Deadline Exceeded
Missing Items
3
No active evidence gaps are listed.
Deadline Status
Overdue / escalation ready
27 days open in the visible workflow.
Recommended Action
Escalate to State
This is the fastest next move from the current workflow stage.
Dossier completeness
Dossier has not been generated yet. Evidence presence is not treated as complete.
US dispute readiness
Evidence packet check
Operational preflight for US warranty escalation: packet size, chronology, cross-references, witness checks, source grounding, and backup evidence.
Estimated pack size
6
Proxy count from docs, images, comments, and claim lines. Actual PDF pages still need final preflight.
Evidence packet lane
Compact packet candidate
Small enough for a compact escalation packet, assuming final PDFs stay clean.
Chronology
Ready to order
Visible span: Oct 6, 2026, 12:30 PM to Oct 23, 2026, 2:55 AM.
Indexed evidence
4 docs / 0 images
Use only the strongest evidence in the escalation packet; keep the rest as support material.
Cross-reference base
Available
Line items, comments, or gap flags can be tied back to supporting material.
Witness verification
Human verification required
Any statement or affidavit output must be checked by the witness before use.
AI / citation gate
Manual check required
Escalation material must keep facts, inferences, citations, and source documents separated.
Expert evidence pressure
Not signalled
No expert-evidence trigger is visible from the current image rollup.
Escalation posture
Monitor
27 days open in the visible workflow; risk score 0.00.
Claim Summary
Evidence summary
No evidence summary yet.
Path
/home/openclaw/nas/Dropbox/MYRV 12024/8- Claims Paid/October 2026/Rpod/74156/Paid claim.pdf
Timeline
First seen Oct 6, 2026, 12:30 PM • last seen Oct 23, 2026, 2:55 AM
Evidence flags
No active evidence gap flags
Comment Intelligence
Thread depth
4 indexed side comments on this claim.
Latest visible thread signal
Oct 22, 2026, 10:16 AM • processor • Paid $255.94 check 3244702 10/20/2026
Role mix
Dealer 0 • OEM 0 • Processor 4
Decision cues
Denial signals 0 • info / missing-doc asks 0 • approval signals 1
Best move
Thread shows approval language — verify payment / closeout.
Quick Actions
Back to search results
Run the same search again.
Open focused evidence thread
Jump straight into Dropbox side comments, notes, and support documents.
Open claim explorer
Return to the main recovery queue view.
Open evidence room
See the quick-rule cards first, then open the legal basis only if needed.
Images
No browser-previewable images were available for this claim yet.
Claim Lines
complaint
CUSTOMER STATES SLIDE WENT OUT SLOW & WHEN RETRACTED HEARD A LOUD NOISE LIKE SOMETHING BROKE
needs-review • confidence 0.29
complaint
CUSTOMER STATES SLIDE WENT OUT SLOW & WHEN RETRACTED HEARD A LOUD NOISE LIKE SOMETHING BROKE
needs-review • confidence 0.00
cause
Customer complaint slide room going out slow Coming in heard a loud pop like something broke Found a bat strip next to the H column on the inside front that had been pulled away from the wall from the top to about halfway down Found three loose screws on the outside on the H column Found a missing screw on the rear bottom rail Also found the system appeared to be very dry and in need of lubrication *25431*
partial-match • confidence 0.41
cause
Customer complaint slide room going out slow Coming in heard a loud pop like something broke Found a bat strip next to the H column on the inside front that had been pulled away from the wall from the top to about halfway down Found three loose screws on the outside on the H column Found a missing screw on the rear bottom rail Also found the system appeared to be very dry and in need of lubrication *25431*
needs-review • confidence 0.04
correction
Connected the unit to shore power level lid on the pin jack as close as possible Ran the slide out, noticed that it seemed to be a little sticky Checked seal compression on the inside on both sides it did have proper seal connection on the inside went outside. Took measurements on the front of the slide room on the rails from the rail to the outside of the H column on the bottom was 2 1/2 inches on the top was 2 7/16 the rails were parallel front to back at 59 1/2 inches measurement from the H column to the inside of the outer flange at the bottom was 33 5/8 inches the top 33 and three-quarter inches At the rear from the rail to the outside of the H column top and bottom 2 1/2 inches, the rails were parallel front and back at 59 1/2 inches another measurement on the slide room at the top and bottom was 33 7/8 inches that is from the H column on the side of the unit to the inside of the outer flange . All measurements were with intolerance Conducted a full inspection of the Wilce did not find any damage to the rails however, I did find that the rollers are the wheels on the rails seem to be very dry I went ahead and lubricated top and bottom inside the H column on the rollers, lubricated the rails both front and back. I tightened down the screws that I found loose on the outside of the edge column and added the screw on the inside rear bottom rail Ran the slide in and out several times the slide was going out smoothly coming in smoothly I reattach the bat strip on the front next to the H column I let the slide room stay out for a period of time. Ran it and let it stay in for a period of time run it back out the slide room is moving in and out properly and equal going out and coming in
matched • confidence 0.75
correction
Connected the unit to shore power level lid on the pin jack as close as possible Ran the slide out, noticed that it seemed to be a little sticky Checked seal compression on the inside on both sides it did have proper seal connection on the inside went outside. Took measurements on the front of the slide room on the rails from the rail to the outside of the H column on the bottom was 2 1/2 inches on the top was 2 7/16 the rails were parallel front to back at 59 1/2 inches measurement from the H column to the inside of the outer flange at the bottom was 33 5/8 inches the top 33 and three-quarter inches At the rear from the rail to the outside of the H column top and bottom 2 1/2 inches, the rails were parallel front and back at 59 1/2 inches another measurement on the slide room at the top and bottom was 33 7/8 inches that is from the H column on the side of the unit to the inside of the outer flange . All measurements were with intolerance Conducted a full inspection of the Wilce did not find any damage to the rails however, I did find that the rollers are the wheels on the rails seem to be very dry I went ahead and lubricated top and bottom inside the H column on the rollers, lubricated the rails both front and back. I tightened down the screws that I found loose on the outside of the edge column and added the screw on the inside rear bottom rail Ran the slide in and out several times the slide was going out smoothly coming in smoothly I reattach the bat strip on the front next to the H column I let the slide room stay out for a period of time. Ran it and let it stay in for a period of time run it back out the slide room is moving in and out properly and equal going out and coming in
partial-match • confidence 0.61
Evidence Thread
Stephanie Kendziorski
processor • Oct 6, 2026, 2:11 PM
Submitted PA 2829912
Stephanie Kendziorski
processor • Oct 7, 2026, 11:06 AM
@Brian P Approved 1.25 and will have shop supplies
Stephanie Kendziorski
processor • Oct 7, 2026, 7:12 PM
Submitted for payment
Stephanie Kendziorski
processor • Oct 22, 2026, 10:16 AM
Paid $255.94 check 3244702 10/20/2026
Claim Files
74156F.pdf
main-pdf • Oct 7, 2026, 12:40 PM • 313,346 bytes
/home/openclaw/nas/Dropbox/MYRV 12024/7- Claims in Process/7.1- Claims Submitted- iCS/Rpod/74156/74156F.pdf
74156F.pdf
main-pdf • Oct 7, 2026, 12:40 PM • 313,346 bytes
/home/openclaw/nas/Dropbox/MYRV 12024/6-Ready to Submit/Rpod/74156/74156F.pdf
74156.pdf
main-pdf • Oct 6, 2026, 12:29 PM • 313,254 bytes
/home/openclaw/nas/Dropbox/MYRV 12024/2-Pre-Authorizations Pending- iCS/Rpod/74156/74156.pdf
74156.pdf
main-pdf • Oct 6, 2026, 12:29 PM • 313,254 bytes
/home/openclaw/nas/Dropbox/MYRV 12024/1- Pre-Authorizations Needed- iCS/Rpod/74156/74156.pdf